BS ISO 10649-6:2012 BSl Standards Publication Cutter arbors with parallel key and tenon drive Part 6: Dimensions and designation of tool holders with modular taper interface with ball track system bsi. ..making excellence a habit BS ISO 10649-6:2012 BRITISH STANDARD National foreword This British Standard is the UK implementation ofIS0 10649-6:2012. The UK participation in its preparation was entrusted to Technical Committee MTE/18, Tools tips and inserts for cutting applications. A list of organizations represented on this committee can be obtained on request to its secretary. This publication does not purport to include all the necessary provisions of a contract. Users are responsible for its correct application. @ The British Standards Institution 2012. Published by BSI Standards Limited 2012 ISBN978 0580718434 ICS25.060.20 Compliance witha British Standard cannot confer immunity from legal obligations. This British Standard was published under the authority of the Standards Policy and Strategy Committee on 30 September 2012 Amendments issued since publication Date Text affected BS ISO 10649-6:2012 INTERNATIONAL ISO STANDARD 10649-6 First edition 2012-07-15 Cutter arbors with parallel key and tenon drive- Part 6: Dimensions and designation of tool holders withmodulartaperinterface withball track system Mandrins porte-fraise a entrainement par clavette et tenon- Partie 6: Dimensions et désignation des porte-outils avec interface a conemodulaire avec systeme de serrage a bille Reference number ISO 10649-6:2012(E) @ ISO 2012 BSISO10649-6:2012 ISO10649-6:2012(E) COPYRIGHTPROTECTEDDOCUMENT ISO 2012 All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized in any form or by any means, electronic or mechanical, including photocopying and microfilm, without permission in writing from either ISO at the address below or ISO's member body in the country of the requester. ISO copyright office Case postale 56 : CH-1211 Geneva 20 Tel. + 41 22 749 01 11 Fax + 41 22 749 09 47 E-mail [email protected] Web www.iso.org Published in Switzerland ii @IsO2012-Allrightsreserved BSISO10649-6:2012 ISO10649-6:2012(E) Foreword IsO (the International Organization for Standardization) is a worldwide federation of national standards bodies Electrotechnical Commission (IEC) on all matters of electrotechnical standardization. International Standards are drafted in accordance with the rules given in the ISO/lEC Directives, Part 2. The main task of technical committees is to prepare International Standards. Draft International Standards International Standard requires approval by at least 75 % of the member bodies casting a vote. rights. IsO shall not be held responsible for identifying any or all such patent rights. ISO10649-6waspreparedbyTechnicalCommitteeISO/TC29,Smalltools,SubcommitteeSC2,Highspeed steelcuttingtoolsandtheirattachements. IsO10649 consists of thefollowingparts,underthegeneral title Cutterarbors with parallelkeyandtenon drive Part 1: General dimensions Part3:Dimensionsand designation of toolholders with7/24taperforautomatictool changers Part 4:Dimensions and designation of tool holders with 7/24 taper without automatic tool changers Part5:Dimensionsanddesignationoftoolholderswithpolygonaltaperinterfacewithflangecontactsurface Part 6:Dimensions anddesignation of tool holders with modulartaper interfacewithball track system ISO 2012 -All rights reserved ili BS ISO 10649-6:2012 ISO10649-6:2012(E) Introduction The aim of isO 10649 (all parts) is to specify the main dimensions for tool holders for this type of interface, and prevent the risk of collision when exchanging the assembled tool within the machine tools iv @ISO2012-All rightsreserved BS ISO 10649-6:2012 INTERNATIONALSTANDARD ISO 10649-6:2012(E) Cutter arbors with parallel key and tenon drive - Part 6: Dimensions and designation of tool holders with modular taper interface with ball track system 1 Scope This part of iso 10649 specifies t